XBMC Community Forum
A6-PACK ☆ ISK 300-90 picoPSU HTPC A6-3500 Very Silent! - Printable Version

+- XBMC Community Forum (http://forum.xbmc.org)
+-- Forum: Off-Topic (/forumdisplay.php?fid=34)
+--- Forum: Hardware for XBMC (/forumdisplay.php?fid=112)
+--- Thread: A6-PACK ☆ ISK 300-90 picoPSU HTPC A6-3500 Very Silent! (/showthread.php?tid=128009)

Pages: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109

RE: Antec ISK 300-65 HTPC A6-3500 - eskro - 2012-04-11 01:57

i talked with ASROCK AMERICA,
you know what, you can buy 'only' the CIR RECEIVER from there directly!
i have the email of the employee to contact!
its $10USD only free shipp!!
since your gonna use the ASROCK mobo,
u should give it a shot!!
Power ON from cold baby!!

Re: RE: Antec ISK 300-65 HTPC A6-3500 - jack0w - 2012-04-11 02:39

(2012-04-11 01:57)eskro Wrote:  i talked with ASROCK AMERICA,
you know what, you can buy 'only' the CIR RECEIVER from there directly!
i have the email of the employee to contact!
its $10USD only free shipp!!
since your gonna use the ASROCK mobo,
u should give it a shot!!
Power ON from cold baby!!

That's annoying, I just ordered one of those CIR receivers for Intel boards! Am planning to have a go at repinning the connector myself as I didn't want to fork out for a useless remote when I have a harmony.

Shame they don't advertise you can get the receiver on its own. Certainly would have been easier!

Will they ship it to people outside the states?

RE: Antec ISK 300-65 HTPC A6-3500 - eskro - 2012-04-11 02:43

well, im in CANADA, they said its not problem.
for EUROPE, i dunno.

but dont be mad, the CIR receiver from INTESET
is the best way to go honestly!
yeah it requires a bit of work, but still,
u wont regret it!

Re: Antec ISK 300-65 HTPC A6-3500 - jack0w - 2012-04-11 02:54

Just keeping my fingers crossed the instructions make sense when I get it in front of me Tongue

Then will have to decide where to mount it!

RE: Antec ISK 300-65 HTPC A6-3500 - eskro - 2012-04-11 02:58

which instructions?

Re: Antec ISK 300-65 HTPC A6-3500 - jack0w - 2012-04-11 03:06

Well I say instructions.. They are actually for repining the connector for different Asrock board. That said I'm hoping the pin configuration will be the same.

Will be doing some more research before I attempt it, as sure it will take a while to get to me!

I'll post the link to the instructions I found when I'm on my laptop tomorrow Smile

RE: Antec ISK 300-65 HTPC A6-3500 - bluray - 2012-04-11 03:11

(2012-04-11 02:39)jack0w Wrote:  That's annoying, I just ordered one of those CIR receivers for Intel boards! Am planning to have a go at repinning the connector myself as I didn't want to fork out for a useless remote when I have a harmony.
If you're talking about this "Inteset CIR", you are getting a better CIR....and the instruction can be found here "Interset CIR receiver with ASRock motherboard?". If you have question on it, you can ask those guys in their forum for help too.

Re: Antec ISK 300-65 HTPC A6-3500 - jack0w - 2012-04-11 03:15

That's the one! Thanks for finding the link.

Good to know the forums are active, in case I do run into problems Smile

RE: Antec ISK 300-65 HTPC A6-3500 - eskro - 2012-04-11 03:23

(2012-04-11 03:06)jack0w Wrote:  I'll post the link to the instructions I found when I'm on my laptop tomorrow Smile

[Image: fPuxg.png]

Smile

RE: Antec ISK 300-65 HTPC A6-3500 - Beer40oz - 2012-04-11 03:44

(2012-04-10 12:06)eskro Wrote:  
(2012-04-06 22:26)Beer40oz Wrote:  But after reading on power consumption from here,
I decided to get a 120W power brick just to be safe.

:"When we place load on the AMD A6 3500 APU,
we see the power draw rise to 85 Watts:"

something important to know here,
during the test performed at guru3d.com,
the motherboard used was a --> ASRock A75 PRO4 FM1 ATX..

Yepp, the test wasn't conducted on a mini-ITX mainboard
but instead, it was done on a FULL ATX mainboard!!

proof --> http://www.guru3d.com/article/amd-a6-3500-apu-review/7

no wonder why they get ~85W under load...

Here's another interesting thread to read --> A6-3500 Power Consumption

Yup that was a Full ATX mobo..... now I wan't that 90w power brick..... I already ordered that 120w..... man. I will try to spend the extra 8 bucks and get that 90w brick. Also that 90w brick the tip is at an angle witch I like.