2014-04-10, 21:48
I had that removed already, I rebooted again but now via XBMC gui instead of the console, not sure if that makes a difference, but i do see the sub sites now! thanks
wget -O xbmc-13-20140411-nc3.tar.gz http://goo.gl/bRCUld --no-check-certificate
pv xbmc-13-20140411-nc3.tar.gz | tar xzf - -C /home/pi/.upgrade
sudo cp /home/pi/.upgrade/xbmc-13-20140411-nc3/{fixup_x.dat,start_x.elf} /boot
ln -sfn /home/pi/.upgrade/xbmc-13-20140411-nc3/xbmc-bcm /home/pi/.xbmc-current
sudo reboot
Quote:Couple of new things to test. The list of refresh rates now contains pal and ntsc variants (e.g. 24 and 23.98).
If most of your content is 23.98 you can set the system refrsh to 23.98 and you won't have the hdmi switching delay when playing most content.
If you set "adjust refresh rate to match video" to always and then play a file with a framerate that changes, or is incorrectly reported in container
(e.g. mediainfo reports different framerate/original framerate because video is 23.98fps, but actual frames are at 25fps) then TV will adjust refresh rate when this is discovered.
This may mean the TV adjusts at start, and then again after few seconds.
There is a chance this could false alarm, so report if any video triggers this when you don't believe it should.
Changing "adjust refresh..." to on start/stop should avoid the new behaviour.
14:22:12 139.802856 T:2840589376 WARNING: Unable to resolve: XBMC_VDR_vnsi.pvr ADDON_Announce, reason: /home/pi/.upgrade/xbmc-13-20140411-nc3/xbmc-bcm/xbmc-bin/share/xbmc/addons/pvr.vdr.vnsi/XBMC_VDR_vnsi.pvr: undefined symbol: ADDON_Announce
14:22:12 139.803391 T:2840589376 ERROR: Unable to resolve exports from dll /home/pi/.upgrade/xbmc-13-20140411-nc3/xbmc-bcm/xbmc-bin/share/xbmc/addons/pvr.vdr.vnsi/XBMC_VDR_vnsi.pvr
14:22:12 139.824127 T:2840589376 WARNING: UpdateAndInitialiseClients - failed to create add-on VDR VNSI Client, status = 6
14:22:12 139.826538 T:2840589376 WARNING: UpdateAndInitialiseClients - failed to load the dll for add-on VDR VNSI Client, disabling it
14:22:12 139.829376 T:2900763712 NOTICE: Thread AddonStatus pvr.vdr.vnsi start, auto delete: true
wget -O xbmc-13-20140413-nc3.tar.gz http://goo.gl/xhtCDY --no-check-certificate
pv xbmc-13-20140413-nc3.tar.gz | tar xzf - -C /home/pi/.upgrade
sudo cp /home/pi/.upgrade/xbmc-13-20140413-nc3/{fixup_x.dat,start_x.elf} /boot
ln -sfn /home/pi/.upgrade/xbmc-13-20140413-nc3/xbmc-bcm /home/pi/.xbmc-current
sudo reboot
(2014-04-13, 23:09)miappa Wrote: Not going to help, but working fine here.I use a non default username and password. Anyway I've fixed it - even though the username and password were still in guisettings.xml and worked when reverting to the old build, when I went into the GUI the username was in fact blank...(could have sworn it wasn't when I first checked)
Both from phone and ipad, ios 6 and 7, and both with Constellation and the official app.
I don't use password though.