Frodo & Gotham Linux Builds for Amlogic M3 Devices

  Thread Rating:
  • 1 Votes - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Post Reply
dlxs84 Offline
Junior Member
Posts: 9
Joined: Mar 2014
Reputation: 0
Post: #226
dhead, I tried compiling from your source using the gotham branch, all seems to go well but then I get prompted for username and password for github and I cant get an output image. I sent you a pm about it as well, if you could help that would be much appreciated, I'd like to help with these builds in any way I can as well. Thanks
find quote
daclina Offline
Junior Member
Posts: 6
Joined: Nov 2007
Reputation: -10
Post: #227
Hey Everyone,

Firstly, thank you very much to dhead for his efforts on this.

I have a Vodoke Playstaq device that I got free with my broadband subscription. It's one of these (http://en.ocworkbench.com/tech/m1-mibox-...ox-review/) and I can't imagine it being very popular. After playing around with XBMC for Android, I decided to look at how it would work under XBMC for linux under M3, I found this thread and after some research I found that some of the devices listed under the Mygica A11 buld have similar hardware to the Playstaq. A few weeks ago I decide to flash it with the Mygica A11 build (using the built in upgrade option) and I now have it running quite solidly for around 2 weeks.

Things I have noticed:

1) CPU usage was at 100% from boot. After much trial and error, the culprit was the menu. If I disabled all the unnecessary items I didn't need it only uses up what looks like 20-40% vs 100% before. I have max 5 menu items and it works for me.
2) I am running the Aeon Nox Minimalistic theme. It reports a varied 20-40 fps. It runs a bit faster than the default confluence theme that comes with the build.
3) Browsing Series and Movies can be quite sluggish (but workable) when you have a large collection and have the cover wall enabled with fanart as background.
4) Wireless works fine but after extended use it was unable to play remotely, although I was able to get to my network np. Simple restart fixes this. No issues with Wifi passwords.
5) 1080p output works 100%
6) 1080p playback is good - I have managed to play with no delay, 8 / 10 different type of files that I tried. 2 had delay, but I am not 100% sure why they are so different. I can run them through G-Spot and find out why.

I have 3 questions and I am hoping somebody can help me here:

a) I am unsure how to upgrade to the next build, if there is ever a new one? I could speak to my ISP and see if they can give me a recovery image so that I can restore Android and upgrade to Linux again, but I would prefer not to. Any suggestions here?
b) I would like to add Mplayer as an external player for the files that I am unable to play / play with A/V lag using DVDPlayer, but I am not sure how to do this on Linux through SSH (I have seen some guides online but they are for Raspberry Pi or from much earlier builds of XBMC). Any suggestions?
c) The default remote that comes with the device has some issues with the buttons under this build (back is esc, home is picture add-ons). Is there a simple way to assign them to different options?

Anyway, thanks again to dhead and thanks to all the rest of the help from this thread.
find quote
fravel Offline
Junior Member
Posts: 5
Joined: Aug 2012
Reputation: 0
Post: #228
Here's waiting anxiously for the next release. This one is working pretty good, axcept the trouble with audio with low khz. Any fix?
find quote
Garza Offline
Junior Member
Posts: 2
Joined: Aug 2014
Reputation: 0
Post: #229
(2014-07-29 07:59)dhead Wrote:  Hi all,

I didn't have time lately for pushing out updated builds as I wasn't quite well for a while.
I'm a bit drowning in books and exams but I'm not abandoning this thread.

Sorry to hear about you not feeling well dhead, nothing serious I hope.
I was pleased to hear that you wouldn't be abandoning the thread, as the gotham build could do with an update when you have time on your side.
I think fravel has mentioned here about an issue with sound that maybe you could take a look at, I have one that might sound trivial regarding the mouse pointer speed when using my Logitech k400, when moving the pointer it appears slightly 'laggy', could this be in the rom or is it a compatibility issue?, I'm using a gbox midnight 2.1 with the last gotham you built, the power on and off button when using the remote can also be a bit unresponsive at times, but on the whole I think you've done a great job in keeping these devices going, thanks again and I hope we can expect an update when you have time.
find quote
dhead Offline
Donor
Posts: 612
Joined: May 2010
Reputation: 2
Post: #230
@Garza

Thanks, I'm much better now (but it was a loud wake up call, like life telling you to set your priorities straight).

I've been away for a few weeks from my build machine and my laptop drive crashed (darn Murphy, it wasn't backed up).
Probably next week I'll be able to access my build machine and if no major issue will arise then I'll upload a new build, but I won't have time to look into bugs.
find quote
Garza Offline
Junior Member
Posts: 2
Joined: Aug 2014
Reputation: 0
Post: #231
(2014-08-13 09:30)dhead Wrote:  @Garza

Thanks, I'm much better now (but it was a loud wake up call, like life telling you to set your priorities straight).

I've been away for a few weeks from my build machine and my laptop drive crashed (darn Murphy, it wasn't backed up).
Probably next week I'll be able to access my build machine and if no major issue will arise then I'll upload a new build, but I won't have time to look into bugs.
Thanks dhead for the quick reply, that's great news about the update, and all the best with your exams.
find quote
spager Offline
Junior Member
Posts: 22
Joined: Feb 2012
Reputation: 0
Post: #232
@Dhead

Glad to hear you are feeling better.

I am posting to let you know that I sold me G.Box 2.0 clone so no worries on my particular post asking for fixes.

Btw it worked great except for wifi and pass through hd audio.

Thanks for the great work done.
find quote
fravel Offline
Junior Member
Posts: 5
Joined: Aug 2012
Reputation: 0
Post: #233
Glad you're back and feeling well. Hope for a new build that fixes the less than 22000khz problem. By the way, are you planning on having the latest librtmp into the build? Userdata?
Best of luck with your exams.
find quote
randompunteruk Offline
Junior Member
Posts: 9
Joined: Jan 2014
Reputation: 0
Post: #234
Hi,

I have one of these:

http://www.ebluetimes.com/en/ProductView...SortID=206
http://www.ebay.co.uk/itm/Bluetimes-3584...1c419925ba

It has an Amlogic 8726 M3 1.2 GHz CPU.

I have tried a few images:

Bluetimes M3 (M3_LINUX-BlueM3-update-20140525.zip) - does not boot.
GBOX 2.0 (M3_LINUX-GBOX_2.0-update-20140525.zip) - boots but USB does not work, so I can't do anything.
Image posted by dreamers: http://d-h.st/NeZ - the UI works but the ethernet and wifi do not

I am relatively technically savvy, so if someone can give me some pointers - e.g. how to get to a command line and dump some logs, I can do so.

Thanks for your help.

Ashley
(This post was last modified: 2014-08-19 00:32 by randompunteruk.)
find quote
arcannis Offline
Junior Member
Posts: 1
Joined: Aug 2014
Reputation: 0
Post: #235
@dhead
Thks for the image. Congrats for the work.

If possible can you tell me where is located the sshd.conf

thks

arcannis
(This post was last modified: 2014-08-19 14:13 by arcannis.)
find quote
randompunteruk Offline
Junior Member
Posts: 9
Joined: Jan 2014
Reputation: 0
Post: #236
If anyone has a little time to take a look, the dmesg output for my bluetimes m3 running M3_LINUX-GBOX_2.0-update-20140525.zip is below.

The ethernet is clearly working, but I can't use either of the remotes I have to control the UI - the remote control works fine in the image posted by dreamers (but the ethernet and wifi don't, and the forum thread for Droidtv linux xbmc is nowhere near as active as this one, so I'll stick with you guys!).

Thanks for any help anyone can provide.

randompunter

Code:
[    0.000000] Linux version 2.6.34.14 (dhead@domU-deb32-sid-01) (gcc version 4.4.1 (Sourcery G++ Lite 2010q1-202) ) #1 Sun May 25 00:22:05 EDT 2014
[    0.000000] CPU: ARMv7 Processor [412fc094] revision 4 (ARMv7), cr=10c53c7d
[    0.000000] CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[    0.000000] Machine: AMLOGIC MESON3 8726M SKT SH
[    0.000000] Ignoring unrecognised tag 0x00000000
[    0.000000] bankstart=0x8f200000, size=0x10d00000
[    0.000000] bankstart=0xa0000000, size=0x20000000
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] On node 0 totalpages: 216320
[    0.000000] free_area_init_node: node 0, pgdat c090a660, node_mem_map c0994000
[    0.000000]   Normal zone: 1280 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 116736 pages, LIFO batch:31
[    0.000000]   HighMem zone: 768 pages used for memmap
[    0.000000]   HighMem zone: 97536 pages, LIFO batch:31
[    0.000000] BUG: mapping for 0x84000000 at 0xc4000000 overlaps vmalloc space
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 214272
[    0.000000] Kernel command line: rootfstype=ext3 androidboot.resolution=1080p rootwait init=/init console=ttyS0,115200n8 nohlt logo=osd1,0x84100000,loaded,1080p a9_clk=600M clk81=187500000 mem=1024m root=/dev/mtdblock5 rw rootfstype=yaffs2 init=/sbin/init
[    0.000000] osd1:1
[    0.000000] loaded:268435459
[    0.000000] logo has been loaded
[    0.000000] 1080p:8
[    0.000000] (CTS_DDR_CLK) = 480MHz
[    0.000000] (CTS_MALI_CLK) = 240MHz
[    0.000000] (CTS_A9_CLK) = 600MHz
[    0.000000] CLK81(from MSR_CLK_REG) = 187000000MHz, a9_clk(from args) = 187500000
[    0.000000] set CLK81 to 178MHz
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 64MB 269MB 128MB 384MB = 845MB total
[    0.000000] Memory: 848308k/848308k available, 16972k reserved, 393216K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
[    0.000000]     vmalloc : 0xe8800000 - 0xf0000000   ( 120 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe8000000   ( 640 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .init : 0xc0008000 - 0xc0038000   ( 192 kB)
[    0.000000]       .text : 0xc0038000 - 0xc08b9024   (8709 kB)
[    0.000000]       .data : 0xc08ba000 - 0xc090afa0   ( 324 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [ttyS0] enabled
[    0.230168] Calibrating delay loop... 933.88 BogoMIPS (lpj=4669440)
[    0.480188] Mount-cache hash table entries: 512
[    0.482163] Initializing cgroup subsys freezer
[    0.486086] Initializing cgroup subsys bfqio
[    0.490425] CPU: Testing write buffer coherency: ok
[    0.495926] devtmpfs: initialized
[    0.500877] NET: Registered protocol family 16
[    0.503624] L2X0 cache controller enabled
[    0.506868] power hold set high!
[    0.510122] set_vccio and set_vccx2 power up
[    0.514319] set_hdmi power up
[    0.517264] usb_wifi_power On
[    0.520293] select eth clk-2,source=750000000,out=50000000
[    0.525874] meson_eth_reset
[    0.628300] SPDIF output.
[    0.629811] ***m1_init_machine: usb set mode.
[    0.629838] USB PHY clock souce: XTAL input divided by 2
[    0.635017] register lm device 0
[    0.638249] register lm device 1
[    0.641498] chip version=e3833402
[    0.644713] major number 0 for disp
[    0.648238] register tv module server ok
[    0.652379] major number 0 for disp
[    0.655860] register tv module server ok
[    0.677714] bio: create slab <bio-0> at 0
[    0.678248] SCSI subsystem initialized
[    0.680058] libata version 3.00 loaded.
[    0.680204] usbcore: registered new interface driver usbfs
[    0.685433] usbcore: registered new interface driver hub
[    0.690768] usbcore: registered new device driver usb
[    0.698685] Advanced Linux Sound Architecture Driver Version 1.0.22.1.
[    0.702582] Switching to clocksource Timer-E
[    0.707149] NET: Registered protocol family 2
[    0.710947] IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.718302] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[    0.725885] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[    0.732089] TCP: Hash tables configured (established 65536 bind 65536)
[    0.738030] TCP reno registered
[    0.741136] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    0.746957] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    0.753311] NET: Registered protocol family 1
[    0.757759] RPC: Registered udp transport module.
[    0.762178] RPC: Registered tcp transport module.
[    0.766892] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.788959] highmem bounce pool size: 64 pages
[    0.794277] VFS: Disk quotas dquot_6.5.2
[    0.794515] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.800870] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.806762] Registering the dns_resolver key type
[    0.809670] Slow work thread pool: Starting up
[    0.814167] Slow work thread pool: Ready
[    0.817982] NTFS driver 2.1.29 [Flags: R/W].
[    0.822601] yaffs built May 25 2014 00:21:49 Installing.
[    0.822648] fuse init (API version 7.13)
[    0.826706] SGI XFS with security attributes, large block/inode numbers, no debug enabled
[    0.835405] msgmni has been set to 888
[    0.840692] alg: No test for stdrng (krng)
[    0.842087] io scheduler noop registered
[    0.845916] io scheduler deadline registered
[    0.850492] io scheduler cfq registered
[    0.854159] io scheduler bfq registered (default)
[    0.867874] brd: module loaded
[    0.870031] loop: module loaded
[    0.871164] PPP generic driver version 2.4.2
[    0.873667] PPP MPPE Compression module registered
[    0.877601] NET: Registered protocol family 24
[    0.881952] PPPoL2TP kernel driver, V1.0
[    0.885819] tun: Universal TUN/TAP device driver, 1.6
[    0.890867] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    0.897291] usbcore: registered new interface driver asix
[    0.902422] usbcore: registered new interface driver qf9700
[    0.907994] usbcore: registered new interface driver sr9600
[    0.913607] usbcore: registered new interface driver cdc_acm
[    0.919109] cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
[    0.927577] Initializing USB Mass Storage driver...
[    0.932476] usbcore: registered new interface driver usb-storage
[    0.938410] USB Mass Storage support registered.
[    0.943109] usbcore: registered new interface driver usbserial
[    0.948848] USB Serial support registered for generic
[    0.953848] usbcore: registered new interface driver usbserial_generic
[    0.960323] usbserial: USB Serial Driver core
[    0.964680] USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter
[    0.972929] usbcore: registered new interface driver belkin
[    0.978423] belkin_sa: v1.2:USB Belkin Serial converter driver
[    0.984259] USB Serial support registered for cp210x
[    0.989216] usbcore: registered new interface driver cp210x
[    0.994690] cp210x: v0.09:Silicon Labs CP210x RS232 serial adaptor driver
[    1.001496] USB Serial support registered for FTDI USB Serial Device
[    1.007831] usbcore: registered new interface driver ftdi_sio
[    1.013485] ftdi_sio: v1.5.0:USB FTDI Serial Converters Driver
[    1.019335] USB Serial support registered for GSM modem (1-port)
[    1.025308] usbcore: registered new interface driver option
[    1.030824] option: v0.7.2:USB Driver for GSM modems
[    1.035917] mice: PS/2 mouse device common for all mice
[    1.041334] usbcore: registered new interface driver xpad
[    1.046312] xpad: X-Box pad driver
[    1.049909] i2c /dev entries driver
[    1.053256] Linux video capture interface: v2.00
[    1.057814] au0828 driver loaded
[    1.061035] usbcore: registered new interface driver au0828
[    1.066519] uvc_init amlogic
[    1.069429] usbcore: registered new interface driver uvcvideo
[    1.075067] USB Video Class driver (v1.1.0)
[    1.080245] device-mapper: ioctl: 4.17.0-ioctl (2010-03-05) initialised: dm-devel@redhat.com
[    1.089258] usbcore: registered new interface driver hiddev
[    1.093215] usbcore: registered new interface driver usbhid
[    1.098776] usbhid: USB HID core driver
[    1.102565] start init vout module
[    1.106146] create  vout attribute ok
[    1.109960] ge2d_init
[    1.112147] ge2d_dev major:253
[    1.115466] ge2d start monitor
[    1.118487] osd_init
[    1.120586] [osd0] 0x84100000-0x850fffff
[    1.124735] Frame buffer memory assigned at phy:0x84100000, vir:0xe9000000, size=16384K
[    1.132459] ---------------clear framebuffer0 memory size=1000000.
[    1.152224] [osd1] 0x85100000-0x860fffff
[    1.152547] Frame buffer memory assigned at phy:0x85100000, vir:0xeb000000, size=16384K
[    1.158608] init fbdev bpp is :24
[    1.162204] osd probe ok  
[    1.164770] vout2_init_module enter
[    1.168252] start init vout2 module
[    1.171869] create  vout2 attribute ok
[    1.176527] UART_ttyS0:(irq = 90, address = 0xf81004c0)
[    1.180919] UART_ttyS1:(irq = 26, address = 0xf11084c0)
[    1.186115] UART_ttyS2:(irq = 75, address = 0xf11084dc)
[    1.191341] UART_ttyS3:(irq = 93, address = 0xf1108700)
[    1.196515] Port 0 = IRQ 90
[    1.199271] Port 1 = IRQ 26
[    1.202043] Port 2 = IRQ 75
[    1.204814] Port 3 = IRQ 93
[    1.207601] Amlogic nand flash Kernel driver, Version K1.03.009 (c) 2010 Amlogic Inc.
[    1.215381] ####Version of Uboot must be newer than U1.03.010!!!!!
[    1.221770] bus_cycle=17, bus_timing=10, start_cycle=10, end_cycle=10,system=5.3ns
[    1.229494] No NAND device found.
[    1.232663] NAND device id: 2c 68 4 4a a9 0
[    1.236717] NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron C revision NAND 4GiB MT29F32G-C)
[    1.246087] #####aml_nand_init, with RB pins and chip->chip_delay:20
[    1.252375] bus_cycle=4, bus_timing=5, start_cycle=5, end_cycle=6,system=5.3ns
[    1.259485] oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH30_1K_MODE
[    1.269789] aml_chip->oob_fill_cnt =0,aml_chip->oob_size =224,bch_bytes =54
[    1.276770] Creating 1 MTD partitions on "C revision NAND 4GiB MT29F32G-C":
[    1.283638] 0x000000000000-0x000000400000 : "bootloader"
[    1.289696] bus_cycle=17, bus_timing=10, start_cycle=10, end_cycle=10,system=5.3ns
[    1.296815] No NAND device found.
[    1.299963] NAND device id: 2c 68 4 4a a9 0
[    1.303998] NAND device: Manufacturer ID: 0x2c, Chip ID: 0x2c (Micron C revision NAND 4GiB MT29F32G-C)
[    1.874976] 1 NAND chips detected
[    1.875024] #####aml_nand_init, with RB pins and chip->chip_delay:20
[    1.879153] bus_cycle=4, bus_timing=5, start_cycle=5, end_cycle=6,system=5.3ns
[    1.886248] oob size is not enough for selected bch mode: NAND_BCH60_1K_MODE force bch to mode: NAND_BCH30_1K_MODE
[    1.896571] aml_chip->oob_fill_cnt =0,aml_chip->oob_size =224,bch_bytes =54
[    1.903487]  oob layout use nand base oob layout oobsize = 16,oobmul =2,mtd->oobsize =448,aml_chip->oob_size =224
[    1.953846] aml nand read data ecc plane0 failed at page 23040 chip 0
[    1.954968] aml nand read data ecc plane1 failed at page 23040 chip 0
[    1.961327]  NAND detect Bad block at 5a00000
[    1.969457] aml nand env valid addr: ffffffffffe00000
[    1.970842] CONFIG_ENV_SIZE=0x2000; ENV_SIZE=0x1ffc; bbt=0x1330; default_environment_size=0xccc
[    1.970857] nand env: nand_env_probe.
[    1.974844] set nand parts for chip 4096MB
[    2.005176] aml nand read data ecc plane0 failed at page 23040 chip 0
[    2.006296] aml nand read data ecc plane1 failed at page 23040 chip 0
[    2.012657]  NAND detect Bad block at 5a00000
[    2.225150] Creating 7 MTD partitions on "C revision NAND 4GiB MT29F32G-C":
[    2.226567] 0x000000c00000-0x000001000000 : "boot_env"
[    2.233431] 0x000001000000-0x000002000000 : "aml_logo"
[    2.242186] 0x000002000000-0x000003000000 : "recovery"
[    2.247573] 0x000003000000-0x000004400000 : "boot"
[    2.254234] 0x000004400000-0x000024400000 : "system"
[    2.261228] aml nand read data ecc plane0 failed at page 23040 chip 0
[    2.262352] aml nand read data ecc plane1 failed at page 23040 chip 0
[    2.268716]  NAND detect Bad block at 5a00000
[    2.422887] 0x000024400000-0x000030400000 : "cache"
[    2.482238] 0x000030400000-0x000100000000 : "userdata"
[    3.501458] ethernetinit(dbg[c09517e8]=0)
[    3.501662] find phy phy_Identifier=7c0f1
[    3.503896] *****WARNING: Haven't setup MAC address! Using random MAC address.
[    3.511131] mac-addr: 0:f4:eb:d3:3a:43
[    3.514809] write mac add to:e7edf148: 00 f4 eb d3 3a 43 |....:C|
[    3.520897] eth0: mixed no checksumming and other settings.
[    3.527048] ethernet_pm_driver init
[    3.529910] ethernet_pm_driver probe!
[    3.533565] dwc_otg: version 2.60a 22-NOV-2006
[    3.538002] dwc_otg lm0: start=0xf9040000
[    3.538012] dwc_otg lm0: core work at High speed.
[    3.538019] dwc_otg lm0: DMA config: BURST_INCR16
[    3.538185] ge2d workqueue monitor start
[    3.956417] dwc_otg lm0: Working on port type = HOST
[    3.956435] DWC_otg: Using DMA mode
[    3.956452] dwc_otg lm0: DWC OTG Controller
[    3.958583] dwc_otg lm0: new USB bus registered, assigned bus number 1
[    3.965040] dwc_otg lm0: irq 30, io mem 0x00000000
[    3.969834] DWC_otg: Init: Port Power? op_state=1
[    3.974458] DWC_otg: Init: Power Port (0)
[    3.978998] hub 1-0:1.0: USB hub found
[    3.982180] hub 1-0:1.0: 1 port detected
[    3.986307] dwc_otg lm1: start=0xf90c0000
[    3.986316] dwc_otg lm1: core work at High speed.
[    3.986324] dwc_otg lm1: DMA config: BURST_INCR16
[    4.406417] dwc_otg lm1: Working on port type = HOST
[    4.406437] DWC_otg: Using DMA mode
[    4.406454] dwc_otg lm1: DWC OTG Controller
[    4.408566] dwc_otg lm1: new USB bus registered, assigned bus number 2
[    4.415048] dwc_otg lm1: irq 31, io mem 0x00000000
[    4.419839] DWC_otg: Init: Port Power? op_state=1
[    4.424466] DWC_otg: Init: Power Port (0)
[    4.428963] hub 2-0:1.0: USB hub found
[    4.432187] hub 2-0:1.0: 1 port detected
[    4.436391] Amlogic A/V streaming port init
[    4.441459] regist mpeg12 codec profile
[    4.444081] regist mpeg4 codec profile
[    4.447812] amvdec_vc1 module init
[    4.451191] regist vc1 codec profile
[    4.454694] amvdec_avs module init
[    4.458133] amvdec_h264 module init
[    4.461572] regist h264 codec profile
[    4.465174] amvdec_h264mvc module init
[    4.468990] regist mjpeg codec profile
[    4.472622] amvdec_real module init
[    4.476142] regist real codec profile
[    4.480354] Vsync pts inc(before): 1500
[    4.483536] Vsync pts inc(after): 1497
[    4.488037] pdev_id = 0, plat_udelay = 2, plat_timeout = 100
[    4.493193] aml gpio i2c bus [0] initialized
[    4.497329] Keypad Driver
[    4.500260] input: aml_keypad as /devices/platform/m1-kp.0/input/input0
[    4.506753] remote config major:249
[    4.510112] physical address:0xa7f32000
[    4.513811] Key input Driver init.
[    4.517242] Key 116 registed.
[    4.520227] input: key_input as /devices/platform/m1-keyinput.0/input/input1
[    4.527296] Key input register input device completed.
[    4.532307] key_input major:248
[    4.536377] Memory Card media Major: 253
[    4.539541] card max_req_size is 128K
[    4.543555] card creat process sucessful
[    4.547184] [dsp]DSP start addr 0xc4000000
[    4.551143] [dsp]register dsp to char divece(232)
[    4.560360] DSP pcmenc stream buffer to [0xa6801000-0xa6a01000]
[    4.561661] amlogic audio dsp pcmenc device init!
[    4.566627] amlogic audio spdif interface device init!
[    4.573175] DSP log stream buffer to [0xa7180000-0xa71fffe0]
[    4.577119] <FIQ>:Deinterlace: Init 100us T
[    4.577125] 0
[    4.582803] amlogic audio dsp log device init!
[    4.587624] aml_rtc aml_rtc: rtc core: registered aml_rtc as rtc0
[    4.593923] ir810_poweroff_init
[    4.596786] ir810_poweroff_probe, status reg = 0xfffa
[    4.601687] gpio dev major number:241
[    4.605441] create gpio device success
[    4.608974] efuse===========================================
[    4.614714] efuse: device efuse created
[    4.618395] efuse--------------------------------------------
[    4.624382] HDMI DEBUG: amhdmitx_init [1452]
[    4.628354] HDMI DEBUG: amhdmitx_probe [1286]
[    4.632923] hdmin get hdmi platform data
[    4.636548] HDMI DEBUG: amhdmitx_probe [1358]
[    4.640974] aml_dvb_init
[    4.643492] DVB: registering new adapter (amlogic-dvb)
[    4.650666] DVB: async fifo 0 buf size 524288, flush size 262144
[    4.654550] DVB: async fifo 1 buf size 524288, flush size 262144
[    4.660835] aml_wdt_init, register platform driver...
[    4.665746] aml_wdt_probe, driver probe ok
[    4.670054] usbcore: registered new interface driver snd-usb-audio
[    4.675848] No device for DAI aml-dai0
[    4.679550] ***Entered sound/soc/aml/aml_m3.c:aml_m3_audio_probe
[    4.685761] ***Entered sound/soc/aml/aml_m3_codec.c:aml_m3_register
[    4.691815] Set HDMI:Chip C
[    4.694511] hdmin get brd phy data
[    4.697852] hdmi phy setting
[    4.700758] hdmin get brd phy data
[    4.704053] hdmi phy setting
[    4.707019] CEC Init
[    4.709627] input: Unspecified device as /devices/virtual/input/input2
[    4.715769] CEC Init done
[    4.720078] HDMI irq 0
[    4.720511] HDMI Error: Unkown HDMI Interrupt source Process_Irq
[    4.726532] HDMI DEBUG: hdmi_task_handle [1018]
[    4.796431]
[    4.796437] SD/MMC initialization started......
[    5.236624] begin SDIO check ......
[    5.284788] SEND OP timeout @1
[    5.285004] begin SD&SDHC check ......
[    5.296840] set type to SDHC
[    5.326631] aml-pcm 0:preallocate_dma_buffer: area=ffc27000, addr=a73c0000, size=65536
[    5.329492] iec958 -3964928: preallocate dma buffer start=00040000, size=c097bae4
[    5.336724] aml-pcm 1:preallocate_dma_buffer: area=ffc78000, addr=a73e0000, size=65536
[    5.344319] asoc: AML-M3 <-> aml-dai0 mapping ok
[    5.349020] ***Entered sound/soc/aml/aml_m3.c:aml_m3_codec_init:
[    5.354927] dapm: AML_M3_CODEC: configuring unknown pin LINPUT1
[    5.360807] dapm: AML_M3_CODEC: configuring unknown pin RINPUT1
[    5.366680] dapm: AML_M3_CODEC: configuring unknown pin HP MIC
[    5.372467] dapm: AML_M3_CODEC: configuring unknown pin FM IN
[    5.378473] input: AML-M3 hp_switch as /devices/platform/soc-audio/sound/card0/input3
[    5.386784] ALSA device list:
[    5.388924]   #0: AML-M3 (AML_M3_CODEC)
[    5.393033] Netfilter messages via NETLINK v0.30.
[    5.397510] nf_conntrack version 0.5.0 (13254 buckets, 53016 max)
[    5.404041] CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
[    5.410881] nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
[    5.418735] sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
[    5.425297] ctnetlink v0.93: registering with nfnetlink.
[    5.430346] xt_time: kernel timezone is -0000
[    5.435818] ip_tables: (C) 2000-2006 Netfilter Core Team
[    5.439882] arp_tables: (C) 2002 David S. Miller
[    5.444420] TCP cubic registered
[    5.448419] NET: Registered protocol family 10
[    5.454244] IPv6 over IPv4 tunneling driver
[    5.457659] NET: Registered protocol family 17
[    5.460595] NET: Registered protocol family 15
[    5.465210] Bridge firewalling registered
[    5.469014] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[    5.475710] All bugs added by David S. Miller <davem@redhat.com>
[    5.481825] enter meson_pm_probe!
[    5.484993] meson_pm_probe done 0x0 200!
[    5.488960] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    5.496965] registered taskstats version 1
[    5.501732] aml_rtc aml_rtc: setting system clock to 1970-01-01 00:07:14 UTC (434)
[    5.508647] yaffs: dev is 32505861 name is "mtdblock5" rw
[    5.513489] yaffs: passed flags ""
[    5.516900] yaffs: Attempting MTD mount of 31.5,"mtdblock5"
[    5.516975] yaffs2 check point aml nand read data ecc plane0 failed at page 23040 chip 0
[    5.525145] aml nand read data ecc plane1 failed at page 23040 chip 0
[    5.606700] failed.
[    5.617091] aml nand read data ecc plane0 failed at page 23040 chip 0
[    5.618210] aml nand read data ecc plane1 failed at page 23040 chip 0
[    5.624556]  NAND detect Bad block at 5a00000
[    5.628992] block 12 is bad
[    5.932516] Actual delay time in sd_voltage_validation() = 40 ms
[    5.932967] S18A : 0
[    6.171337] Got RCA = 17793
[    6.250414]
[    6.250421] ***********CID*************
[    6.250442] 02:54:4d:53:44:31:36:47:40:d1:3a:93:14:00:96:00:
[    6.255627] MID[8]=2
[    6.257994] OID[16]=TM
[    6.260304] PNM[40]=SD16G
[    6.262903] PRV[8]=64
[    6.265155] PSN[32]=0x14933ad1
[    6.268202] Reserved[4]=0
[    6.270785] year[8].month[4]=2009.6
[    6.274249] NotUsed[1]=0
[    6.276776] CRC[7]=0
[    6.276779]
[    6.359131]
[    6.359138] ********** CSD v2 **************
[    6.359321] 40:0e:00:32:5b:59:00:00:77:7f:7f:80:0a:40:00:00:
[    6.364778] CSD_STRUCTURE[2]=1
[    6.368002] Reserved1[6]=0
[    6.370667] TAAC[8]=14
[    6.373005] NSAC[8]=0
[    6.375258] TRAN_SPEED[8]=50
[    6.378133] CCC[8+4]=0x5b5
[    6.380801] READ_BL_LEN[4]=9
[    6.383659] READ_BL_PARTIAL[1]=0
[    6.386882] WRITE_BLK_MISALIGN[1]=0
[    6.390329] READ_BLK_MISALIGN[1]=0
[    6.393706] DSR_IMP[1]=0
[    6.396218] Reserved2[4]=0
[    6.398920] Reserved3[2]=0
[    6.401588] C_SIZE[4+8+8]=30591
[    6.404706] Reserved4[1]=0
[    6.407404] ERASE_BLK_EN[1]=1
[    6.410336] SECTOR_SIZE[6+1]=127
[    6.413541] WP_GRP_SIZE[7]=0
[    6.416409] WP_GRP_ENABLE[1]=0
[    6.419430] Reserved5[2]=0
[    6.422115] R2W_FACTOR[3]=2
[    6.424887] WRITE_BL_LEN[2+2]=9
[    6.428016] WRITE_BL_PARTIAL[1]=0
[    6.431296] Reserved6[5]=0
[    6.433981] FILE_FORMAT_GRP[1]=0
[    6.437196] COPY[1]=0
[    6.439438] PERM_WRITE_PROTECT[1]=0
[    6.442902] TMP_WRITE_PROTECT[1]=0
[    6.446280] FILE_FORMAT[2]=0
[    6.449149] Reserved7[2]=0
[    6.451823] CRC[7]=0
[    6.453989] NotUsed[1]=0
[    6.453991]
[    6.693997]
[    6.694005] ***********SCR*************
[    6.694029] 02:b5:00:00:1c:02:92:02:
[    6.697139] SD_SPEC[4]=2
[    6.699824] SCR_STRUCTURE[4]=0
[    6.702855] SD_BUS_WIDTHS[4]=5
[    6.705887] SD_SECURITY[3]=3
[    6.708762] DATA_STAT_AFTER_ERASE[1]=1
[    6.712469] Rsv1[7]=0
[    6.714721] SD_SPEC3[1]=0
[    6.717331] CMD_SUPPORT[2]=0
[    6.720178] Rsv2[6]=0
[    6.722431] Reserved2[32]=43123228
[    6.722434]
[    6.963366]
[    6.963374] ****************switch status****************
[    6.964688] Data_Struction_Verion : 0
[    6.968347] Max_Current_Consumption : 200
[    6.972311] Support[0] : 0x8001    Busy[0] : 0x0
[    6.976658] Support[1] : 0x8001    Busy[1] : 0x0
[    6.980971] Support[2] : 0x8001    Busy[2] : 0x0
[    6.985302] Support[3] : 0x8001    Busy[3] : 0x0
[    6.989633] Support[4] : 0x8001    Busy[4] : 0x0
[    6.993963] Support[5] : 0x8003    Busy[5] : 0x0
[    6.998294] Function_Group_Status6 : 0
[    7.002018] Function_Group_Status5 : 0
[    7.005747] Function_Group_Status4 : 0
[    7.009483] Function_Group_Status3 : 0
[    7.013191] Function_Group_Status2 : 0
[    7.016926] Function_Group_Status1 : 1
[    7.016929]
[    7.100583]
[    7.100590] ****************switch status****************
[    7.101901] Data_Struction_Verion : 0
[    7.105538] Max_Current_Consumption : 200
[    7.109543] Support[0] : 0x8001    Busy[0] : 0x0
[    7.113853] Support[1] : 0x8001    Busy[1] : 0x0
[    7.118184] Support[2] : 0x8001    Busy[2] : 0x0
[    7.122515] Support[3] : 0x8001    Busy[3] : 0x0
[    7.126857] Support[4] : 0x8001    Busy[4] : 0x0
[    7.131176] Support[5] : 0x8003    Busy[5] : 0x0
[    7.135506] Function_Group_Status6 : 0
[    7.139241] Function_Group_Status5 : 0
[    7.142955] Function_Group_Status4 : 0
[    7.146693] Function_Group_Status3 : 0
[    7.150404] Function_Group_Status2 : 0
[    7.154128] Function_Group_Status1 : 1
[    7.154131]
[    7.159421] set sd_mmc config_reg->cmd_clk_divide 1, CLK 46M
[    7.164956] sd_mmc_init() is completed successfully!
[    7.169909] This SDHC card is working in Wide Bus and High Speed mode!
[    7.169914]
[    7.256963]  cardblksd: cardblksd1
[    7.493099] monitor : INSERT
[   12.134112] yaffs_read_super: isCheckpointed 0
[   12.134164] VFS: Mounted root (yaffs2 filesystem) on device 31:5.
[   12.140002] devtmpfs: mounted
[   12.140036] init_post.
[   12.140075] Freeing init memory: 192K
[   12.143619] BFS CPU scheduler v0.318 by Con Kolivas.
[   12.148597] run_init_process /sbin/init.
[   12.398514] save exit: isCheckpointed 1
[   12.495631] save exit: isCheckpointed 1
[   12.944458] yaffs: dev is 32505863 name is "mtdblock7" rw
[   12.944484] yaffs: passed flags ""
[   12.947761] yaffs: Attempting MTD mount of 31.7,"mtdblock7"
[   12.948319] yaffs2 check point failed.
[   15.004338] yaffs_read_super: isCheckpointed 0
[   15.202421] <30>udevd[109]: starting version 182
[   17.829990] netdev_open
[   17.830015] Ethernet reset
[   17.830033] NET MDA descpter start addr=e6582800
[   17.834810] write mac add to:e7edf148: 00 f4 eb d3 3a 43 |....:C|
[   17.840231] Current DMA mode=0
[   17.843969] ether leave promisc module
[   17.847036] ether leave all muticast module
[   17.851150] set hash low=2,high=0
[   17.854921] set hash low=2,high=1
[   17.858647] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   19.847096] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   19.847393] set hash low=2,high=8001
[   29.946428] eth0: no IPv6 routers present
[   30.340598] set hash low=2,high=18001
[   33.723515] Mali<2>:
[   33.723535] Mali<2>: Inserting Mali v9 device driver.
[   33.725349] Mali<2>: Compiled: May 25 2014, time: 00:22:17.
[   33.730893] Mali<2>: Svn revision:
[   33.736512] Mali<2>: MMU memory system initializing
[   33.739213] Mali<2>: Rendercore: subsystem global mutex initialized
[   33.745446] Mali<2>: Core: subsystem_init: Mali-400 PP
[   33.750556] Mali<2>: Core: subsystem_init: Mali-400 GP
[   33.755664] Mali<2>: Mali L2 cache system initializing
[   33.816103] mali_meson_poweron: Interrupt received.
[   33.816986] Mali<2>: MMU registered
[   33.818922] Mali<2>: MMU registered
[   33.822365] Mali<2>: Mali OS memory allocator created with max allocation size of 0x8000000 bytes, cpu_usage_adjust 0x00000000
[   33.835155] Mali<2>: Memory Validator 'Framebuffer' installed for Mali physical address base==0x84000000, size==0x06000000, cpu_adjust==0x00000000
[   33.846908] Mali<2>: Creating Mali L2 cache: Mali-400 L2 cache
[   33.853004] Mali<1>: Mali memory allocators will be used in this order of preference (lowest numbered first) :
[   33.862612] Mali<1>:     5: Mali Memory
[   33.867219] Mali<2>: Attach mmu: 0xe61c7360 to core: Mali-400 PP in subsystem: Mali-400 PP
[   33.874334] Mali<2>: Attach mmu: 0xe61c73c0 to core: Mali-400 GP in subsystem: Mali-400 GP
[   33.882563] Mali<2>: Mali L2 cache system load complete
[   33.888017] Mali: Mali device driver  loaded
[   33.892003] Mali<2>: malidrv_build_info
[   33.967109] warning: `proftpd' uses 32-bit capabilities (legacy support in use)
[   38.557756] aml_m3_codec_mute mute=1
[   38.595390] aml_m3_codec_mute mute=1
[   38.598823] aml_m3_codec_mute mute=1
[   38.602372] aml_m3_codec_mute mute=1
[   38.607276] aml_m3_codec_mute mute=1
[   39.380842] buf=0
[   39.380865] IEC958_mode_raw=0
[   39.391447] ***Entered sound/soc/aml/aml_dai.c:aml_dai_hw_params
[   39.392708] I2S hw init,i2s mode 0
[   39.395287] iec958 mode PCM16
[   39.398317] IEC958 16bit
[   39.400741] iec958 nodify hdmi audio type 1
[   39.404899] audio info changed.notify to hdmi: type 1,sr 44100
[   39.411443] HDMI: aout notify rate 44100
[   39.414598] HDMI: aout notify format PCM
[   39.418995] aml_m3_codec_mute mute=0
[   39.432826] I2S hw init,i2s mode 0
[   39.432854] iec958 mode PCM16
[   39.433630] IEC958 16bit
[   39.436140] iec958 nodify hdmi audio type 1
[   39.440959] aml_m3_codec_mute mute=0
[   39.477089] ***Entered sound/soc/aml/aml_pcm.c:aml_audio_clock_gating_enable
[   40.712920] Mali<2>: MMU session begin
[   40.712987] Mali<2>: Page directory for session 0xe61d0980 placed at physical address 0xA6344000
[   40.725258] Mali<2>: MMU session begin: success
[   40.725298] Mali<2>: Core: session_begin: for Mali-400 PP
[   40.730206] Mali<2>: Core: session_begin: for Mali-400 GP
[   40.754603] tvmode set to 720p
[   40.754639] TV mode 720p selected.
[   40.754648] [0x1b7e] = 0xff
[   40.754974] [0x1b80] = 0x0
[   40.757750] [0x1b57] = 0x0
[   40.760345] [0x104f] = 0x40003
[   40.763376] [0x1058] = 0x40e8
[   40.766321] [0x107f] = 0x8c0000c3
[   40.769638] [0x105c] = 0x1043e
[   40.772644] [0x1066] = 0x10843
[   40.775675] [0x1bb8] = 0x52
[   40.778471] [0x1b62] = 0x2029
[   40.781392] [0x1b8d] = 0x4040
[   40.784336] [0x1b8e] = 0x19
[   40.787126] [0x1b94] = 0x288
[   40.789966] [0x1b95] = 0xc87
[   40.792824] [0x1b97] = 0xce3
[   40.795682] [0x1b98] = 0x50
[   40.798469] [0x1b99] = 0xf0
[   40.801226] [0x1b9a] = 0x50
[   40.803997] [0x1b9b] = 0x2b0
[   40.806876] [0x1b9c] = 0xcb0
[   40.809714] [0x1b9d] = 0x4
[   40.812399] [0x1b9e] = 0x8
[   40.815084] [0x1ba1] = 0x4
[   40.817786] [0x1ba2] = 0x8
[   40.820454] [0x1ba4] = 0x288
[   40.823312] [0x1ba3] = 0xc87
[   40.826178] [0x1ba6] = 0x1d
[   40.828962] [0x1baf] = 0x2ec
[   40.831800] [0x1ba7] = 0x100
[   40.834658] [0x1ba8] = 0xa8
[   40.837444] [0x1ba9] = 0xa8
[   40.840202] [0x1baa] = 0x100
[   40.843060] [0x1bab] = 0x0
[   40.845745] [0x1bac] = 0x5
[   40.848495] [0x1bae] = 0x2ed
[   40.851288] [0x1b68] = 0x100
[   40.854147] [0x1b60] = 0x0
[   40.856849] [0x1b6e] = 0x200
[   40.859690] [0x1b58] = 0x0
[   40.862375] [0x1b7e] = 0x0
[   40.865060] [0x1b64] = 0x9061
[   40.868019] [0x1b65] = 0xa061
[   40.870949] [0x1b66] = 0xb061
[   40.873894] [0x1b78] = 0x1
[   40.876599] [0x1b79] = 0x1
[   40.879265] [0x1b7a] = 0x1
[   40.881949] [0x1b7b] = 0x1
[   40.884634] [0x1b7c] = 0x1
[   40.887333] [0x1b7d] = 0x1
[   40.890005] [0x1bfc] = 0x1000
[   40.892949] [0x1c0d] = 0x3210
[   40.895894] [0x1c0e] = 0x54
[   40.898693] [0x1b57] = 0x0
[   40.901351] [0x1b80] = 0x1
[   40.904038] mode is: 6
[   40.906377] VPU_VIU_VENC_MUX_CTRL: 0xa
[   40.910117] viu chan = 1
[   40.912611] VPU_VIU_VENC_MUX_CTRL: 0xa
[   40.916344] new mode 720p set ok
[   40.921157] Vsync pts inc(before): 1500
[   40.923438] Vsync pts inc(after): 1497
[   40.928268] set mode VIC 4 (cd0,cs0,pm1,vd0,1)
[   40.931667] param->VIC:4
[   40.934178] mode is: 6
[   40.936573] VPU_VIU_VENC_MUX_CTRL: 0xa
[   40.940240] viu chan = 1
[   40.942753] VPU_VIU_VENC_MUX_CTRL: 0xa
[   40.946547] hdmin get brd phy data
[   40.949854] hdmi phy setting
[   40.953957] hdmin get brd phy data
[   40.956090] hdmi phy setting
[   40.959089] Sink is DVI device
[   40.963010] No sink attached
[   40.966716] osd0 free scale DISABLE
[   40.968516] osd1 free scale DISABLE
[   40.992381] video disable try be changed to 0 by xbmc.bin
[   40.992467] video disable try be changed to 1 by xbmc.bin
[   40.998163] osd0=>x:0 ,y:0,w:1279,h:719
[   40.998170]  osd1=> x:0,y:0,w:0,h:0
[   41.026500] current VIC: 4
[   41.026508] audio sample rate: 2
[   41.026546] PCM out to HDMI
[   41.040024] Time out: AIU_HDMI_CLK_DATA_CTRL
[   41.053505] Time out: AIU_HDMI_CLK_DATA_CTRL
[   41.053512] Enable audio spdif to HDMI
[   41.053564] HDMI Audio Type: PCM
[   41.053800] HDMI: set audio param
[   44.416562] Headphone unpluged
[   99.666568] I2S hw init,i2s mode 0
[   99.666600] iec958 mode PCM16
[   99.667375] IEC958 16bit
[   99.669885] iec958 nodify hdmi audio type 1
[   99.674115] aml_m3_codec_mute mute=0
[  109.680893] aml_m3_codec_mute mute=1
[ 1344.797833] Wrong custom code is 0xa45bff00
[ 1345.168296] Wrong custom code is 0xe916ff00
[ 1345.346501] Wrong custom code is 0xa45bff00
[ 1345.562975] Wrong custom code is 0xf906ff00
find quote
Rod1 Offline
Junior Member
Posts: 10
Joined: Apr 2012
Reputation: 0
Post: #237
Hi randompunter

You need this remote.conf for the Bluetimes M3 unit.

http://pastebin.com/MSqYtVx9
find quote
buczy Offline
Junior Member
Posts: 2
Joined: Aug 2014
Reputation: 0
Post: #238
I've got a gbox m3 amlogic box and the number 4 on the remote does not work. Anyone got a quick fix?
find quote
randompunteruk Offline
Junior Member
Posts: 9
Joined: Jan 2014
Reputation: 0
Post: #239
@Rod1 thanks for that - that let me start playing around with the UI

It looks like the USB bus and devices are not working. No wifi (guessing that it must be on the USB bus) and keyboards/mice don't work. Any tips on how I can debug this?

Thanks,

randompunteruk
find quote
Vathan Offline
Junior Member
Posts: 11
Joined: Apr 2013
Reputation: 0
Post: #240
(2014-08-13 09:30)dhead Wrote:  Probably next week I'll be able to access my build machine and if no major issue will arise then I'll upload a new build, but I won't have time to look into bugs.

Hey dhead - hope everything is good. Just wanted to check in to see if you might be working on a 13.2 final for 2.0 and 2.x M3's?

Thanks for all your work so far.

Vathan
find quote
Post Reply