[LINUX] My Asrock 330 ION Tweaks, Tips, Tricks, and Fixes!

X3lectric Wrote:His chip results on sensors as w83667hg-isa-fff8
Mine isw83667hg-isa-0290

Because the mobos are laid out different it could be his chip ID to His an Foxconn Ion is at a different address to which is being forced....

Would have to have a look at his

Code:

sensors-detect

output and also the result of

Code:

cat /proc/ioports

to see if this is correct though to get the correct id to be forced can only be extracted from what file is found here

on another note I have notice my system reported a fan working at 8823rpm

Today it reports nothing.... Im wondering how much of this other driver is actually correct for a completely different however similar in what they do chip.

Also if it was as simple as this I have to ask why is it that lm-sensors project hasn't already modified the driver and has it released and working I mean they know this backwards...

http://lists.lm-sensors.org/pipermail/lm...27193.html

That link is tied to the request for the diver and lm-sensors as on compat list near bottom on the post below....

http://www.lm-sensors.org/wiki/Devices

This is all a biiiig maybe maybe either way atm

here is my ioports:

jeff@xbmc:~$ cat /proc/ioports
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-0060 : keyboard
0064-0064 : keyboard
0070-0071 : rtc0
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
03c0-03df : vga+
04d0-04d1 : pnp 00:06
0800-080f : pnp 00:06
0cf8-0cff : PCI conf1
4000-407f : pnp 00:06
4000-4003 : ACPI PM1a_EVT_BLK
4004-4005 : ACPI PM1a_CNT_BLK
4008-400b : ACPI PM_TMR
4010-4015 : ACPI CPU throttle
4020-4027 : ACPI GPE0_BLK
4080-40ff : pnp 00:06
4400-447f : pnp 00:06
4480-44ff : pnp 00:06
4484-4484 : ACPI PM2_CNT_BLK
44a0-44af : ACPI GPE1_BLK
4800-487f : pnp 00:06
4880-48ff : pnp 00:06
4900-493f : 0000:00:03.2
4d00-4d3f : 0000:00:03.2
4d00-4d3f : nForce2_smbus
4e00-4e3f : 0000:00:03.2
4f00-4fff : 0000:00:03.0
b800-b80f : 0000:00:0b.0
b800-b80f : ahci
b880-b883 : 0000:00:0b.0
b880-b883 : ahci
bc00-bc07 : 0000:00:0b.0
bc00-bc07 : ahci
c000-c003 : 0000:00:0b.0
c000-c003 : ahci
c080-c087 : 0000:00:0b.0
c080-c087 : ahci
d000-dfff : PCI Bus 0000:03
dc00-dc7f : 0000:03:00.0
e000-efff : PCI Bus 0000:05
ec00-ec7f : 0000:05:00.0
ec00-ec7f : atl1c
fffd-fffe : w83627ehf
fffd-fffe : w83627ehf
jeff@xbmc:~$

Hi,

Could anybody set up 6ch analog on it? (reverse mic in and line in)

I could not set it (ALSA 1.0.22)

Regards> Ivan

@ boybastos

you forgot the output of sensors detect and pls use a pastebin for long ouputs like that.

Also on the post I made a link to find out what the correct chip id would be for your chip

only you can give me those values or post a link to the file e.g. Copy the file and upload file in question via mediafire or similar post only link. thx.

And pls if we are going to be doing this read and provide info as well as look for yourself the contents and links of the posts which are made to you... Its in your best interests... thx.

@ truebada8

There's topics on forums which explain how to set up alsa in Linux. When you install alsa you have to un-mute the channels which are turned off

and no to answer your question I use HDMI for sound only tried stereo analogue with default files no more.

deleted, because of nonsense

truebaba8 Wrote:Could anybody set up 6ch analog on it? (reverse mic in and line in)

My guess is that you need to set that up in the ~/.asoundrc file, but perhaps alsa is clever enough to set up the device by itself by the name of "surround51".

On the command line you could try this with:

monty0815 Wrote:@BoyBastos
according to your /proc/ioports output you seem to have a w83627ehf chip on the board. This is actually good news, as that chip should be supported without forcing anything.
So what happens if you do this?

Code:

sudo modprobe w83627ehf

Some links if you run into problems (such as device busy or similar):

https://bugs.launchpad.net/ubuntu/+sourc...bug/382211
http://hansdegoede.livejournal.com/7932.html

Please post dmesg output etc., otherwise debugging is going to be very hard.

regards,
monty

No he does not when you modprobe force ID chip the cat /proc/ioports reports the chip as w83627ehf

look at mine here at this post both before and after modprobed

if you look at your too will have to say that since your not actually loading a verified compatible driver, if it was lm-sensors project would have released it already.

Of course, you are absolutely right, forget that. I'll edit the post to reflect this.

lol absolute is Vodka innit?

can u get any fan rpm reports I cant anymore so have to wonder whats going on...

X3lectric Wrote:l
can u get any fan rpm reports I cant anymore so have to wonder whats going on...

Just checked, I don't have any readings for fan speed and I don't think I ever had any.

http://forum.xbmc.org/showpost.php?p=500...tcount=166

there it showed then only change was the max cpu temps from 60 to 85 though prob is that tool reports the chipset temp as well both cpus as is.