Crystal HD Driver Error: Update script exited with status: 3

Thanks for confirming what the error code means.

I got the card from Logic Supply back in February/March. Used it successfully in a Dell Mini9 for a while and just moved it into the ATV last weekend. I'll re-seat the card in the ATV and try again. If that doesn't work, I'll put it back in the netbook and confirm it still works there.

No chance that still being on OS 2.2 is causing the card to fail to be recognized for some reason?

OK, I need a little more help here. I put the card back in the Dell Mini and it works. Here it is in the Device Manager:

http://i894.photobucket.com/albums/ac147...iceMgr.jpg

and here's a screenshot of XBMC using it (I think) while playing back a 720p MKV file on the Mini:

http://i894.photobucket.com/albums/ac147...llMini.jpg

So as far as I can determine, the card itself is fine. Put the same card back in the ATV, tried to install the driver via the Launcher script, and still get the Error 3 message.

Any specific logs that the script creates that I could grab and look at? Other ideas on what might be going on?

when in doubt, do the script bits manually.

Ive got exactly the same problem. The card works in a Asus 1000H Netbook but not in the AppleTV, but maybe its the installation. Everything I try to install from the Menuextras or Nito fails.

Ill try a quick restore and rehack, I think its faster then anything else. (or the crystalbuntu image)

Just installed a Crystal HD BCM970015 in my ATV 1. I have followed the steps below to load the drivers:

(2010-02-02 12:33)andy204 Wrote:  This is the easiest way to install the CrystalHD driver onto your AppleTV!

To make this easy install available log into your AppleTV

Code:

ssh frontrow@appletv.local

and enter:

Code:

defaults write com.teamxbmc.xbmclauncher XBMCAdditionalDownloadPlistURLs -array-add http://crystalhd.sartori.at/files/crystalhd.plist

This will add a new download source to your "Downloads" section in Launcher.

Current revision: r174 (Build Date: 20101027)

If you have Problems with a new build, you can enable the last working release CrystalHD r156 (20100826):

Code:

defaults write com.teamxbmc.xbmclauncher XBMCAdditionalDownloadPlistURLs -array-add http://crystalhd.sartori.at/devel/crystalhd.plist

--

and keep getting the "Error: Update script exited with status: 3" using either method.
I have reseated the card several times and still get the same error. I purchased the card from Logic Supply.
I have run Crystalbuntu from a USD stick and played 1080p video with good results, most of the time. Video choppy and hangs sometime. So I think the card is working properly with that OS.

Any idea why I keep getting the Error?

(2010-05-24 06:34)davilla Wrote:  when in doubt, do the script bits manually.

Can you provide instruction on how to do this? I tried to follow the instructions at Google but get stuck with Turbo's kext enabler. I want to determine if my BCM970015 is really defective for sure before I sen it back.

Any help is greatly appreciated!

(2012-03-21 20:15)nunz56 Wrote:  

(2010-05-24 06:34)davilla Wrote:  when in doubt, do the script bits manually.

Can you provide instruction on how to do this? I tried to follow the instructions at Google but get stuck with Turbo's kext enabler. I want to determine if my BCM970015 is really defective for sure before I sen it back.

Any help is greatly appreciated!

Finally got it working!

1. Removed Crystal HD card
2. Did Factory Restore
3. Upddated ATV to 3.0.2
4. Used ATV USB Creator patchstick with all options
5. Installed Launcher and updated
6. ssh into ATV and added CrystalHD Driver for XBMC Launcher - per Andy's post pg. 1
7. Installed Crystal HD drivers-this time without the card being installed-Driver installed successfully!
8. Installed Crystal HD card and rebooted
9. Logged into ATV and ran: sudo dmesg-output indicated Crystal HD card
   

Tried playing back 720 and 1080p with XBMC Eden-ATV OSX and all played very smooth with no problems!

Back to being a Happy XBMC user! Thanks to ALL of the XBMC Team members and Support Forum!
Hope this helps with anyone else having this problem!