Posts: 3
Joined: Nov 2010
Reputation:
0
I built a new computer with Windows 7 and am using my old firefly remote control. I managed to get it to work with Windows Media Center but WMC sucks really badly. It only shows my movie and tv shows grouped under one listing and only lets me scroll through them by file name, no graphics or dvd covers ect.
I am using a old hdtv rear projection tv hooked to my TV via dvi to dvi connection. I currently have it set up on Extended desktop though when I click the Firefly button on the remote, Windows media center opens on the TV instead of the PC Monitor like I want.
How would I program my remote to have it open XBMC just like I have it now , on the TV instead of the PC monitor? I can have it open on both I dont care but I want to use it on the TV. I tried setting it up as a Dupelicate clone setup but the resolution sucks, since its a older tv running dvi.
Posts: 3
Joined: Nov 2010
Reputation:
0
Also, I installed the Android App for my phone and it works ok with the XBMC, so if I cant get my firefly remote to work its not biggie.
A big question is how do I get XBMC to automaticlly come up on my TV monitor instead of just the pc monitor. The android app doesnt seem to have a button to auto open XBMC like I can with WMC and my current remote. And normally I could just drag a program over to the TV Screen desktop and it would automaticlly open there but i cant do that with XBMC.
Posts: 61
Joined: Dec 2009
Reputation:
0
It sounds like your issue is not with the remote, but configuring Windows. The Firefly works well, I use EventGhost with it which does a reasonable job of mapping the keys. You can program EventGhost to start XBMC as a part of it's Autorun (or you can put it into the Windows startup group), but as to which monitor is used I am not sure how to configure that. On my Revo I use the HDMI connector and it works great (it's the only monitor I use though).
Keith
XBMC on Acer Revo, Windows 7.
ATV2.
Intel NUC, Windows 7
Gateway Laptop when traveling...
Posts: 835
Joined: Feb 2007
Reputation:
14
if you have more than one monitor then in Dharma you can choose which one you want to run xbmc on.
EG.
Posts: 582
Joined: Sep 2006
Reputation:
1
I would also recommend EventGhost. I use 2 Firefly remotes for two separate setups at my place and they work wonders. You can program the Firefly button in EventGhost to launch XBMC, move it, maximize it, and give it focus
Posts: 3
Joined: Nov 2010
Reputation:
0
Ok, thanks everyone for the info, Ill look into it. Im pretty much a newbie at all this, I dont know anything about programing and such. Is running Eventghost to set the remote up pretty easy to do?
Posts: 44
Joined: Mar 2010
Reputation:
0
Phokus
Junior Member
Posts: 44
I also have a firefly remote and windows 7 and eventghost.I have a big problem though.
I mapped the up-down-left-right keys as xbmc inputs in event ghost to move up-down-left-right. But apparently i also have to program additional xbmc inputs so that u-d-l-r also does little skip forward/backward and big skip forward/backward. So essentially i have 2 xbmc commands for each key.
This normally doesn't matter except in two instances:
When i bring up the OSD controls and try to move left and right, it also does the little skip forward/backwards at the same time.
When i'm listening to music and i'm trying to navigate through menus, it skips the music as well.
How to prevent this?
Posts: 3
Joined: Oct 2010
Reputation:
0
2010-12-29, 10:21
(This post was last modified: 2010-12-29, 10:43 by kcabrams.)
With XBMC 9.11 I just created a snapstream XBMC.xml remote profile and it worked like a CHARM!
Its no longer working in 10. Any suggestions?
Correction. 9.11 and 10 were both working in Windows XP. I am now running 64bit windows 7. Thats the point where it stopped working