Live TV doesn't work on Openelec [tvheadend server] - Printable Version +- Kodi Community Forum (https://forum.kodi.tv) +-- Forum: Support (https://forum.kodi.tv/forumdisplay.php?fid=33) +--- Forum: General Support (https://forum.kodi.tv/forumdisplay.php?fid=111) +---- Forum: Raspberry Pi (https://forum.kodi.tv/forumdisplay.php?fid=166) +---- Thread: Live TV doesn't work on Openelec [tvheadend server] (/showthread.php?tid=148646) |
RE: Live TV doesn't work on Openelec [tvheadend server] - DarkMike - 2013-05-14 Ok. I'' try this variant today. RE: Live TV doesn't work on Openelec [tvheadend server] - nmcaullay - 2013-05-15 Hi there, is there any news on when/how this fix would/could be incorporated into openelec builds (like rbej custom builds)? (2013-05-09, 10:34)DarkMike Wrote: Aspect ratio problem resolved. RE: Live TV doesn't work on Openelec [tvheadend server] - Jönke - 2013-05-15 Install this .zip https://dl.dropboxusercontent.com/u/6902100/HT/pvr.hts-linux-arm.zip RE: Live TV doesn't work on Openelec [tvheadend server] - pootler - 2013-05-15 eheij, Did you have any luck with your usb patch for the Pi and live tv?? Pootler RE: Live TV doesn't work on Openelec [tvheadend server] - dhead - 2013-05-15 (2013-05-15, 19:14)pootler Wrote: eheij, It isn't his patch. You may want to read more about it here: http://www.raspberrypi.org/phpBB3/viewtopic.php?f=28&t=39175 RE: Live TV doesn't work on Openelec [tvheadend server] - pootler - 2013-05-16 Thanks Dhead. RE: Live TV doesn't work on Openelec [tvheadend server] - ntadej - 2013-05-19 My latest status after tvheadend plugin patch: - 1080i channels: aspect ratio OK - 576i channels: aspect ratio still 1:1 I've also noticed faster channel switching with latest rbej builds. RE: Live TV doesn't work on Openelec [tvheadend server] - mezo - 2013-05-21 i found yesterday the iframe option in the xvdr addon. i was rly happy, but this option cause my stream to stutter and my sound gets always direkt out of sync. without iframe option the stream runs smooth RE: Live TV doesn't work on Openelec [tvheadend server] - stuCONNERS - 2013-05-24 is there any improvement using a usb 3.0 powered hub instead of an usb 2.0 powered hub? RE: Live TV doesn't work on Openelec [tvheadend server] - serxx - 2013-05-24 (2013-05-24, 11:38)stuCONNERS Wrote: is there any improvement using a usb 3.0 powered hub instead of an usb 2.0 powered hub?Only if you use power hungry devices that USB2 hub struggles to power and no external power option. USB3 standard provides 900mA per port instead of 500mA. Other than that there is no reason or advantage to connect USB3 hub to USB2 port. The limiting factor is still the USB2 port and USB2 controller. RE: Live TV doesn't work on Openelec [tvheadend server] - stuCONNERS - 2013-05-25 (2013-05-24, 20:05)serxx Wrote:(2013-05-24, 11:38)stuCONNERS Wrote: is there any improvement using a usb 3.0 powered hub instead of an usb 2.0 powered hub?Only if you use power hungry devices that USB2 hub struggles to power and no external power option. USB3 standard provides 900mA per port instead of 500mA. yes there is an advantage, this has been proven with the use of usb 3.0 sticks on raspbmc compared to usb 2.0 sticks, the data transfer is much higher, im thinking more along the lines of glitches on playback. RE: Live TV doesn't work on Openelec [tvheadend server] - popcornmix - 2013-05-25 (2013-05-25, 00:34)stuCONNERS Wrote: yes there is an advantage, this has been proven with the use of usb 3.0 sticks on raspbmc compared to usb 2.0 sticks, the data transfer is much higher, im thinking more along the lines of glitches on playback. Only because USB 3 sticks tend to have faster flash and controllers inside. We'll still communicate at USB 2 speeds, and so using a USB 3 hub shouldn't make a difference. RE: Live TV doesn't work on Openelec [tvheadend server] - stuCONNERS - 2013-05-25 is there anyway to check the transfer rate over usb? (Except for counting) I can lend a usb 3.0 hub for a few hours. im going to transfer a file with file manager from my usb3.0 raspbmc install to usb 2.0 pendrive, via usb2.0 and then via usb 3.0 hub. if your right there shouldnt be any difference in transfer time. Would this be the correct way of checking this? RE: Live TV doesn't work on Openelec [tvheadend server] - popcornmix - 2013-05-25 (2013-05-25, 12:45)stuCONNERS Wrote: is there anyway to check the transfer rate over usb? (Except for counting) I can lend a usb 3.0 hub for a few hours. im going to transfer a file with file manager from my usb3.0 raspbmc install to usb 2.0 pendrive, via usb2.0 and then via usb 3.0 hub. if your right there shouldnt be any difference in transfer time. Would this be the correct way of checking this? It's one way. I'd do this: Code: openelec:~ # hdparm -t /dev/sda RE: Live TV doesn't work on Openelec [tvheadend server] - stuCONNERS - 2013-05-27 sorry forgot to reply, i tried the usb 3 hub idea, it does make a difference, not a huge one but the file transfers were slightly faster, so unless my usb 2 hub is adding to the bottle neck on the raspberry pi,, i dont know. what needs to be done to make the raspberry pi a proper option for live tv? |